Support

Airam smoke sensor

1. Remove and re-insert the battery

Belkin Wemo lights

1. Turn the light on.
2. Turn the light off for a second and turn it on for 3-2 seconds
3. Repeat the above off/on procedure total 5 times and wait
4. After about 5secs the light flashes for a moment to signal a succefull reset.

Belkin Wemo plug

1. Unplug your Wemo device.
2. Hold down the Restore button.
3. While holding the Restore button down, plug the Wemo device into a power outlet and continue to hold the button down for 5 seconds. The status light will begin to blink orange to signify it is resetting.
4. Release the Restore button. It should take about 60 to 90 seconds for the Wemo device to restore and reboot. It will blink blue and orange or green and orange when finished.

Centralite door/window sensor

1. Eject the battery tray and remove the battery
2. Press down the device reset button
3. While holding down the reset button, reinsert battery in the tray to factory reset the device
4. Pair the device again from the Cozify app’s “Devices” section (“+”-icon at the top right corner)

Centralite flood sensor

1. Eject the battery tray and remove the battery
2. Press down the reset button next to the battery slot with a pencil
3. While still holding down the reset button, reinsert battery and hold the butto down until the light starts to blink in the device.
4. Pair the device again from the Cozify app’s “Devices” section (“+”-icon at the top right corner)

Develco water sensor

1. Open the sensor by turning the plastic cover anti-clockwise. Press the reset button until the LED light starts blinking constantly.
2. Put back on the plastic cover by turning it clockwise.

Develco motion sensor

1. Open the plasic cover by pressing the button and pulling the cover back at the same time.
2. Make sure the plastic wrap has been removed from the battery and that the battery is placed to match the + and - ends.
3. Press the button in the cover until the LED light starts blinking.

Develco smoke sensor

1. Open the sensor's cover by turning it anti-clockwise.
2. Press the reset button until the LED light starts blinking constantly.

Foscam cameras

1. Power on the camera and press the camera's reset button down for 30seconds.
   (In Foscam C1 ja C2 cameras' case you'll hear a separate "reset succeeded" feedback when the reset is done).

Heiman smoke sensor

1. Press with a slim pin the tiny reset hole for 5 seconds until the LED blinks.
2. After this press the hole again with the pin for 2 seconds until the light blinks green, signaling it's ready for pairing.

Heiman keyfob

1. Press with a slim pin the tiny reset hole for 5 seconds until the LED blinks slowly green for 3 seconds.
2. After this press the hole again with the pin for 2 seconds until the light blinks green, signaling it's ready for pairing.

Ikea Floalt lights

1. Turn on the light
2. Turn off/on the light quickly 6 times (in 1 second intervals) and after that leave the light on
3. Wait until the light blinks quickly signalling a successful reset. If the light doesn't blink in a couple of seconds, repeat the on/off procedure a little bit slower/faster until the light blinks in the end.
4. Turn off the light once more for a couple of seconds and turn it back on.

Nyce motion sensor

1. Open the device case
2. Press the reset button inside the case 10 times to reset the device

Osram Lightify plug

1. Take the plug out from the wall.
2. Press the plug's button down and insert the plug to the wall still pressing down the button.
3. Release the button when the plug makes a clicking sound.

Osram Lightify lights

1. Turn the light on for 5 seconds and turn it off for 5 seconds.
2. Repeat this on/off procedure 5 times.
3. Once the resetting is succesfull, the lamp goes once off for a short while.

Philips Hue Dimmer Switch

1. Hold down all four buttons at once.
2. Wait until the led becomes green and release the buttons.
3. The led flashes red-green a couple of times when reset was successful.

Philips Hue lights

1. Resetting the Philips Hue lights a separate Philips Dimmer Switch device is required.
2. Bring Philips Dimmer Switch right next to the the lamp you wish to reset, and press the I and 0 buttons simultanously.
3. Hold these buttons down for 10seconds - until the light flashes a couple of times.

Philips Hue Motion sensor

1. Press and hold the setup button (small hole at the back of the device) for 10 seconds.
2. Orange blinking: sensor is resetted and ready for installation.

Proove power plug

1. Press 5 seconds the button of the plug; the light starts blinking
2. Press once again the button; the plug makes a couple of clicking sounds

Note: In case of multiple Proove plugs, make sure the plugs are further than 1meter away from each other

Place Cozify hub away from blocking metal objects, to as central place as possible. It’s good to always leave a couple of meters distance to your WiFi router.

Sonos wireless speaker

1. Open Sonos' own app
2. At Sonos’ own app, go to “Settings” and select “Reset Controller”